Home About Product Contact Terms



Simco Coatings Inc.
211 Gunther Ln.
Belle Chasse, LA 70037
Office: 504.393.9455
Toll-Free: 866.95.SIMCO
Fax: 504.433.1406




For more information or purchase request

Email: sales@simcocoatings.com

Legal/Privacy Info.
EPOXY POLYAMIDE ZINC PRIMER
MIL-DTL-24441/19B (SH)
FORMULA 159, TYPE-II


Description: This Epoxy-Polyamide two component Zinc Rich Coating is designed to conform the specific composition and performance requirement of Federal Specification MIL-DTL-24441/19B (SH) Formula-159, Type-II and is recommended to be used for painting land and marine structures.

Principal Characteristics:
Excellent rust preventative properties in adverse or chemically polluted atmospheres.
Easy application by airless spray up to 4.0 mils (100 Microns) dry film thickness.
Good adhesion properties on sandblasted steel where a hard durable chemical resistant nonporous coating is desired.
Excellent water and weather resistance for interior and exterior use.
Good impact resistance

Technical Data

Color & Finish: Gray; Flat
Mass Density (mixed): Approx 24.0 lbs./gal.
Solids by Volume: Approx. 65.0%
Zinc Dust Pigment (ASTM D520, TYPE-I): 80%
Flash Point (mixed): Base 99F (38C); Hardener 108F (42C)
Theoretical Spreading Rate: 1040 sq. ft./gal. @ 1 Mil D
Recommended DFT 3-4 Mils (75-100 Microns)
Volatile Organic Compound (VOC): 2.5 lbs./gal., 300 grm./ltr.
Temperature Resistance 250F (121C)
Pot Life 4 hours @ 73F
Shelf Life 12 months
Packaging: A two Component material with base and curing agent supplied in:
1 & 5 Gallons Containers
Mix ratio 4:1 by volume.
Drying Time @ 75F:
To touch 2 hours
Dry hard 6 hours
Max interval before overcoating 7 days
To full cure 7 days

Recommended Substrate Conditions:
Steel: Blast cleaned to a minimum grade SSPC-SP10 (SA2 ) The surface must be perfectly dry.

Instructions for Use:
Power agitate base component to uniform consistency before combining, then again after combining. Do Not vary proportions.

Substrate Temperature:
during application and the first 24 hours of curing, the substrate temperature must be above 41F (5C) and at least 5F ( 3C) above the dew point.

Mixing Instructions:
Ratio: base to hardener 4:1 by volume

The temperature of the mixture of base and hardener during mixing and application should be above 59 F (15C), otherwise more solvents must be used to obtain application viscosity. This results in lower sag resistance and slower cure. Thinner should be added after mixing the components.

Very good mechanical mixing of base and hardener is essential in view of the paste consistency.

Conventional Spray:
Manufacturer: DeVilbiss Binks
Gun Model MBC or JGA #18 or #62
Tip-Air Cap Combination 704E 66PE
Fluid hose should by 3/8" I.D. with a maximum length of 50 feet. Pot should always have dual regulation and be kept at same elevation as spray gun.


Airless Spray:
Manufacturer: Graco Binks DeVilbiss
Gun Model: 205-590 Model 500 JGN-501
Pump: Bulldog Mercury 5C QFA-519
Hose should be 3/8" I.D. minimum, but " whip end section may be used for ease of application. A maximum length of 100 feet is suggested. Best results will be obtained using a .018"-.021" tip at 2400-2700 p.s.i.


Thinning Requirement:
Recommended Thinner  : MIL-24441 Thinner
Airless Spray                  : 0-10% by Volume
Conventional Spray       : 5-15%% by Volume
Clean-up Thinner           : MIL-24441 Thinner

Caution:
Contains flammable solvents. Keep away from sparks and open flames. Use only grounded explosion proof equipment in accordance with the National Electric Code. Workmen must use nonferrous tools, wear conductive and non-sparking shoes in areas where explosion hazards exits.
In confined areas, workmen must wear fresh airline respirators, protective clothing and gloves. Avoid contact with skin, breathing of vapor or spray mist ingestion. Keep out of reach of children.

Non-Warranty:
The technical data listed herein has been compiled for your convenience and guidance, and is based upon our experience and knowledge. However, since we have no control over the use of this information of this product, no warranty expressed or implied, is intended or given. Simco Coatings, Inc. assumes no responsibility whatsoever for coverage, performance, or any other damages, including injuries resulting from use of this information or of products recommended herein.

Copyright 2001-2012 Simco Coatings Inc. All rights reserved.